Display posts from previous
Sort by

problem in progdvb 5.15.10 and vista x64

#1 by man2007
iam used version progdvb 5.15.10 ( 32 bit)
the problem
when need edit in the option select
settings
options
other
i need select refesh channel on lost signal ( because i found problem with my dvb card kworld when go from channel to other channel some time lost the signal )
----------------------------------------------------------------------
when select the ( refesh channel on lost signal )
when exit from progdvb and then restart the progdvb the selective
( refesh channel on lost signal ) is not active ?
------------------------------------------------------------------------
the progdvb settings in
C:\Users\my user\AppData\Local\ProgDVB

Re: problem in progdvb 5.15.10 and vista x64

#4 by Juergen
man2007 wrote:...when exit from progdvb and then restart the progdvb the selective
( refesh channel on lost signal ) is not active ?...
What exactly do you mean?

Station not selected? Or just not set active in your channel list? To find out, tune to another channel and try if you can go back to the previous channel then.

Or tuner not initiated?

Any error message?

...

BTW, the channel refresh should happen automatically, without having to restart ProgDVB.
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#5 by man2007
thank you
i mean this
Image
when active the selection after exit from progdvb the selection not active
( not enable) in next restart progdvb
i whant enable this selection because
some time in hotbird (diseq used port A)
when change from channel to other some time lost signal

#6 by Juergen
I see.
Means, the selection is not getting stored for that option.
Obviously a bug.

Hope Prog reads this.

Meanwhile you may try to change from ProgDVB.ini
In older versions this was located in "Options":
"ResfeshLevel=0", to be changed to "ResfeshLevel=1".
(No typo here, I've just used copy & paste)
AFAIK it's still the same on newer versions.
If that entry does not exist, try to add a line for this.
And perhaps post that whole "Options" section here.
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>