Both free versions (32 and 64 bit) crash permanently on Vista 64 Ultimate and Win7 64 Ultimate during the loading process even after a reinstallation from scratch. This has been happening since at least version 6.70.
Is there a command line switch to narrow down the problem?
I'm using the BDA driver version 3.12.00.00.a of Terratec DT USB XS Diversity.
I have no problems with the 32bit free version on XP32 on the same hardware when I disable the second receiver.
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#2Please send me ProgDVBEngine.log of last prerelease of ProgDVB after crash.
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#3The main window doesn't even start, I only get the attached message.
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#4Do you have same problem if install ProgDVB not to program files? (to c:\progdvb for example)
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#6Even after a complete uninstallation and clearing the registry of any ProgDVB releated entry the problem occurs again after a fresh reinstallation.
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#8Please send me files from log directory.
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#9There are no log entries (where should they be?) as the main window does not start but only the already reported error message is shown.
By the way this happens also after upgrading the GPU driver to version 11.10!
By the way this happens also after upgrading the GPU driver to version 11.10!
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#10What last good version of ProgDVB for you? You can enable logs in old version and install new over.
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#1164 bit version 6.60 is working fine, but it has no Settings->Options->Debug->Logs entry.
how can I activate logs?
how can I activate logs?
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#12Too old...
Other idea is you open ProgDVB.ini file in notepad and add
[Debug]
EnableLogs=1
Other idea is you open ProgDVB.ini file in notepad and add
[Debug]
EnableLogs=1
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#13I have installed version 6.73.1, same problem. The log is attached.
Could the reason be that ProgDVB cannot cope with the twin receiver, because even the older versions only work properly after disabling the second receiver?
Could the reason be that ProgDVB cannot cope with the twin receiver, because even the older versions only work properly after disabling the second receiver?
- Attachments
-
- Logs.zip
- (1008 Bytes) Downloaded 346 times
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#14Very short log... Crash before Engine is starting. I think some files not founded.
ps: Try total remove progdvb.ini
ps: Try total remove progdvb.ini
Re: ProgDVB64 and ProgDVB32 crash on Vista 64bit and Win7 64
#15Program start on Win7_64 after removal of PrgDVB.ini produces same error and same log as before.
On Vista_64 the same error occurs, but the log is slightly different, see attached zip-file.
What is strange for me is the following entry in the ProgDVB.ini:
[Modules]
CurDeviceID=-1,
whereas on XP_32 this entry has a positive value!?
On Vista_64 the same error occurs, but the log is slightly different, see attached zip-file.
What is strange for me is the following entry in the ProgDVB.ini:
[Modules]
CurDeviceID=-1,
whereas on XP_32 this entry has a positive value!?
- Attachments
-
- Logs.zip
- (1023 Bytes) Downloaded 355 times