Hi I can't put work a DiSEqC 1.0 switch with to ports: 1- 30ºW 2-19,2ºE
I only get the port 1 working. can some one tel me if exists some way to debug the protocol to find out where is the probem.
thanks
bthk
Re: DiSEqC 1.0 on skystar s2 express hd
#2Enable logs (everything), change some channels and look in progdvbengine logs for the diseqc messages.
If they are present, try change the diseqc switch, to test it.
If not present, change device configs, till they appear.
Dont put a switch more than 25 m from the dvb card, cable can cause excessive attenuation to signals, may cause malfunction.
If they are present, try change the diseqc switch, to test it.
If not present, change device configs, till they appear.
Dont put a switch more than 25 m from the dvb card, cable can cause excessive attenuation to signals, may cause malfunction.
Re: DiSEqC 1.0 on skystar s2 express hd
#3Hello,
Only today I could test it! I was wrong about the version of DiSEqC that I was using. I have one DiSEqC 2.0 And I testit with one receiver and it works. Now I put the DiSEqC right after the input on the sat card with a two meters cable and it doesn't work.
The logs tel me this:
thanks
Only today I could test it! I was wrong about the version of DiSEqC that I was using. I have one DiSEqC 2.0 And I testit with one receiver and it works. Now I put the DiSEqC right after the input on the sat card with a two meters cable and it doesn't work.
The logs tel me this:
is there any thing that I can do?22:17:02.691 - DevicesManager::SetTransponder 10847000
22:17:02.701 - TransponderManager::SetTransponder (TR) 10847000
22:17:02.710 - Api2Device::SetTransponder 10847000KHz
22:17:02.720 - Diseqc::Cmd 2 1
22:17:02.732 - Api2BaseModule::SendDiseqCmd
22:17:02.742 - cmd:1.0sw; param:1 { E0 10 38 F4 }
22:17:02.977 - tr:freq:10847, pol:V, sr:22000
22:17:03.133 - Api2Device::SetTransponder result OK delay 0 ms
22:17:03.143 - TsInputTrafficProcessor::OpenTransponder 0
22:17:03.153 - FilterManager::OnSetTransponder 10847Mhz
22:17:03.182 - ModuleList::ChangeChannel 0
22:17:03.193 - DvbEpgParser::SetChannel 0
22:17:06.041 - * s:9 q:74 tr=0 (0)
22:17:08.131 - * s:9 q:74 tr=0 (0)
thanks
Re: DiSEqC 1.0 on skystar s2 express hd
#4logs seems ok. Try change device options to Avermedia device, as it is said some topics before.
Re: DiSEqC 1.0 on skystar s2 express hd
#5Hello,
I've been doing some test and the last test was using the aplication that comes with the card that is DVB VIEWER TE2 ( Technisat Edition) and with this I can scan and view channels on second port of diseqc.
For that I setup the diseqc port to Pos B/Opt A.
I gues that are some issues on technisat extend module that is not able to set correct possition of diseqc.
The DVBVIEWR instalations brings some dll for this card. Could this helps the developer to fix some issues?
Wainting forward for an solutions.
Best Regards
I've been doing some test and the last test was using the aplication that comes with the card that is DVB VIEWER TE2 ( Technisat Edition) and with this I can scan and view channels on second port of diseqc.
For that I setup the diseqc port to Pos B/Opt A.
I gues that are some issues on technisat extend module that is not able to set correct possition of diseqc.
The DVBVIEWR instalations brings some dll for this card. Could this helps the developer to fix some issues?
Wainting forward for an solutions.
Best Regards