problem with diseq 1.1 4*1 diseq in twinhan azurewave 1034
iam recived 3 sat (nilesat-hotbird-badr sat) when change from
channel in nilesat to channel in hotbird not work
but work when change from channel on hotbird to other in the same sat hotbird
the problem from Modules
BDA.Device not found in BDAold.Device but in BDAold.Device the CI not work
and thank you to all
#2
Do you receive anything on the third position badr sat ?
Do you receive anything on hotbird, at least occasionally, e.g. did you do your own scan there?
If yes, your 'distinguish by ...' settings may be wrong, test all four possible combinations.
If not, you are out of luck with DiSEqC on your device, probably due to a BDA driver, as those do not support DiSEqC natively, and the proprietary tricks the original software may use are not public..
BTW, for up to four positions in one switch, you don't need DiSEqC 1.1.
Standard 1.0 is enough then.
Do you receive anything on hotbird, at least occasionally, e.g. did you do your own scan there?
If yes, your 'distinguish by ...' settings may be wrong, test all four possible combinations.
If not, you are out of luck with DiSEqC on your device, probably due to a BDA driver, as those do not support DiSEqC natively, and the proprietary tricks the original software may use are not public..
BTW, for up to four positions in one switch, you don't need DiSEqC 1.1.
Standard 1.0 is enough then.
My signature:
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
#3
yes diseq 1.0Juergen wrote:Do you receive anything on the third position badr sat ?
Do you receive anything on hotbird, at least occasionally, e.g. did you do your own scan there?
If yes, your 'distinguish by ...' settings may be wrong, test all four possible combinations.
If not, you are out of luck with DiSEqC on your device, probably due to a BDA driver, as those do not support DiSEqC natively, and the proprietary tricks the original software may use are not public..
BTW, for up to four positions in one switch, you don't need DiSEqC 1.1.
Standard 1.0 is enough then.
and no problem in scan problem when switch from channel from sat to sat
the problem with BDA.Device but not found in BDAold.Device
but the problem in BDAold.Device not work with ci interface
download and try
http://rapidshare.com/files/61793635/Modules.rar.html
with twinhan 1034 azurewave and diseq
thank you..