Dears,
I don't succeed to setup ProgDVB for the creatix SAA7131 card (Medion MD8828 PC). Which device should I select in the ProDVB setup ? I tried the standard DBA, but no luck. Any help would be appreciated.
ThanX
#2
Check the device and drive in system control, to find out, if it's a BDA driver.
If not, you may be out of luck.
If yes, and the original software packet was installed and set up completely, there should be (at least) one specific BDA visible from ProgDVB device list, with a name, that points to your device.
Else you may not have the necessary tuning space registry entries.
If not, you may be out of luck.
If yes, and the original software packet was installed and set up completely, there should be (at least) one specific BDA visible from ProgDVB device list, with a name, that points to your device.
Else you may not have the necessary tuning space registry entries.
My signature:
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
prog dvb and creatix saa 7131 not working
#3Hi!
same problem for me. Using MEDION 8800, Creatix saa 7131.
ProgDVB only finds DVB-T, not DVB-S.
Channel search no results.
Programm crashes "cannot open" , "cannot find BDA" or so
Does not close using task-manager. I have to shut down the PC
Drivers installed:
BdaPlgIn.ax
BdaSup.Sys and many more
WIN XP, SP2, german
ProgDVB5[1].12.9Std and
ProgDVB4.88Std, neither are working
no language files or codecs
reboot does not help
Original software Power Cinema is very slow, but working properly
Did not use it after booting
Thanks for a reply, or a help!!!!!
same problem for me. Using MEDION 8800, Creatix saa 7131.
ProgDVB only finds DVB-T, not DVB-S.
Channel search no results.
Programm crashes "cannot open" , "cannot find BDA" or so
Does not close using task-manager. I have to shut down the PC
Drivers installed:
BdaPlgIn.ax
BdaSup.Sys and many more
WIN XP, SP2, german
ProgDVB5[1].12.9Std and
ProgDVB4.88Std, neither are working
no language files or codecs
reboot does not help
Original software Power Cinema is very slow, but working properly
Did not use it after booting
Thanks for a reply, or a help!!!!!