I Have a new TV Card : Technotrend S2-3200 (Technisat SKYSTAR HD)

BDA Windows Driver: V 5.0.0.19 Technotrend AG 4.3.2006

Device "BDA.Device" V1.52 / Propertties: Technotrend
Channels found by Astra 19.2 scan:
TV Free 46
TV Scrambled 62
Radio Free 4
Radio Scrambled 0
Other Free 14
Other Scrambled 0


Device "anysee.Device" V1.37 Properties anysee (Technotrend does not)
Channels found by Astra 19.2 scan:
TV Free 207
TV Scrambled 287
Radio Free 51
Radio Scrambled 93
Other Free 108
Other Scrambled 16

Is The newer BDA.Device not Compaktible to my Card ?

Greetings, Manfred
Sorry for my brooken english.....

You may want to add some more details, to enable getting closer to the source of your problem.

Do the missing channels / transponder have anything in common, like nothing found above e.g. 11700 MHz, or nothing on Horizontal, or alike?

You can change grouping / sorting criteria of your dynamic list, to find out things like those.
Or simply watch carefully at scan time, or use 'search transponder' manually..

Hallo Jürgen,
Ich hoffe das ich auch in Deutsch antworten darf.

Nun zug Progdvb version habe ich vergessen zu erwähnen:
Progdvb 4.90.8

Ich verwende bei beiden devices
BDA.Device V1.52 und anysee.Device V1.37
die gleiche Hardware, Treiber und einstellungen.
auch DiSEqC nebst transponderlisten.
Sortierungen Filterung gruppierungen nehme ich nicht vor.

der einzige unterschied ist, das bei einem scan auf Astra
mit BDA.Device V1.52 deutlich weniger Sender gefunden werden.
(immer ausgehend von einer geleerten channellist)

Das jetz nur Horizontale oder Vertikale
oder nur Frequenzmässig unten oder oben
kann ich nich sagen, weil beim ganzen scan
H oder V oben oder unten Sender gefunden werden, nur weniger.

Ob der BDA.Device V1.52 Probleme mit DiSEqC hat ?
Vielleich bringt der was durcheinander ?

Ich teste weiter .....

Gruss, Manfred

You can try set addition deley in settings->options->other->scanner

This place is in English.

However, I've just mentioned the sorting / grouping criteria, to perhaps find out a bout some systematical error. Can be undone at any time.

However, the scanner delay Prog recommends is a good idea. Give some more time, as some hardware may not switch fast enough, to allow reading the transponder tables within the default limits.

If you are missing complete transponders, try to tune to them manually, by 'search transponder'.
If not working again, perhaps your LNB's LOFs aren't precise. Detune manually there, in 1 MHz steps up and down, up to +/- 5 MHz, to possibly find out a systematic deviation of the transponders against the nominal value.
In case, correction is done on the LOF settings, same amount, opposite direction.
Keep in mind, each LOF may have it's own offset, to be compensated this way.

Prog wrote:You can try set addition deley in settings->options->other->scanner

Hello,
Thanks fo Info.
I can not Find in Settings, Option, Other
a field or Button with an Name Scanner/delay ????

in Other is
1.) Check CRC for SI packets
2.) Priority
3.) Plugin API:

Thi is Progdvb 4.90.8 (In Help Displayed 4.90.7 ?????)

Greetings, Manfred

This is in 5.x. In 4.x you must manual change in ini file.

Prog wrote:This is in 5.x. In 4.x you must manual change in ini file.

I have more tests with my Technotrend Budget S2-3200

With the anysee.Device i found by
LNB1 (Astra 192) and LNB2 (Hotbird 130 )
only (not all) Stations from Satellite Astra
(some few stations from Hotbird)

With the BDA.Device i found by
LNB1 (Astra 192) and LNB2 (Hotbird 130 )
only some few Stations from Satellite Hotbird

the DiSEqC with both BDA Devices does not correcctly
with the Technotrend Budget S2-3200
(Technisat Skystar HD, not Skystar HD2 !!)

This Problems i have with Progdvb 4
progdvb 5 is a little better, but finds only some few stations

(With my old Card, a Technotrend Premium (Skystar 1)
i have with the same Hardware (Switch/LNB1/LNB2)
and same DiSEqC settigins no Problems.)

This Test with the older BDA Driver from Technotrend 4.4.10.18
The newest driver 5.0.0.19 finds still much less stations ((

Oh i found the Parameter in Pogdvb.ini
(OPTIONS]
AdditionDelayAfterSetTransponder=10

The Scan is not better with this Parameter .....


Greetings Manfred