Need Help
Posted: Wed May 20, 2009 9:04 pm
why then i am scaning diferent satelites, chanels confusing ! for exs: scaning hotbird but at the end its all sirius chanels ...
Thanx
Thanx
Page 1 of 1
Posted: Wed May 20, 2009 10:16 pm
You should post all relevant details on your dish system, to perhaps get helped. Without those it's absolutely impossible...
Posted: Thu May 21, 2009 4:05 pm
Windows Vista, skystar HD2, .... what more ???
satelites Sirius Hotbird Astra
satelites Sirius Hotbird Astra
.
Posted: Thu May 21, 2009 6:02 pm
I am not good undarstand. Do you have channels from both positons in one list? You can change that in channel list properties.
Posted: Thu May 21, 2009 8:13 pm
...with a DiSEqC switch, I suppose.scb wrote:Windows Vista, skystar HD2, .... what more ???
satelites Sirius Hotbird Astra
Or is it a motorized system?
Anyway, Prog is correct, your dynamic channel list(s) can be set up to show positions to your liking (and access), and there can be more than one, and each can hold more than one position.
A channel list is not the original channel data base (where scanned stations go to), but more like a collection of links to it.
This for, you can also force a given satellite list, to show or not show stations from a position, after a successful scan.
Posted: Sat May 23, 2009 3:13 pm
than i scaning astra or hotbird for me writing sirius chanels
.with a DiSEqC switch
.with a DiSEqC switch
Posted: Sat May 23, 2009 11:08 pm
Looks like if your DiSEqC is not switching.
To verify, bypass it temporarily and connect the Astra or Hotbird LNB directly, scan again.
If DiSEqC switching indeed fails, there may be several reasons for this.
Most common cause is not having the proper device settings selected, or using a tuner and driver, that does not yet provide those (on a BDA platform).
But there may also be some different source of trouble, like long and / or bad LNB cables, losing to much of the 22kHz signal, or a bad tuner or switch, or in rare cases grounding or interference problems (like from some nasty switch mode PSUs or CRT monitors / TVs, to close to the LNB cable).
To verify, bypass it temporarily and connect the Astra or Hotbird LNB directly, scan again.
If DiSEqC switching indeed fails, there may be several reasons for this.
Most common cause is not having the proper device settings selected, or using a tuner and driver, that does not yet provide those (on a BDA platform).
But there may also be some different source of trouble, like long and / or bad LNB cables, losing to much of the 22kHz signal, or a bad tuner or switch, or in rare cases grounding or interference problems (like from some nasty switch mode PSUs or CRT monitors / TVs, to close to the LNB cable).
.
Posted: Sun May 24, 2009 5:45 am
What DVB device? it is very depended.
Posted: Sun May 24, 2009 5:44 pm
Device is SkyStar HD2
http://www.technisat.com/index4986.html ... ,en,76-215
with any older version it where good, and now propaly working...
http://www.technisat.com/index4986.html ... ,en,76-215
with any older version it where good, and now propaly working...
.
Posted: Sun May 24, 2009 7:43 pm
This card must work with diseq in ProgDVB. Check settings->Device options. Must selected azurewave.
Posted: Sun May 24, 2009 10:44 pm
thanx for the support 
Posted: Wed Jun 24, 2009 7:50 pm
hi,
after update to 6.10 ver. its all the same like before
after update to 6.10 ver. its all the same like before