Hello,
I had installed the drivers for the broadlogic 2030 tuner, however I cannot get progdvb to recognize the card. It's telling me that it wasn't able to find any BDA drivers.
In device manager, the card shows up as "V@Box ABA2030 Adapter" under Network Adapters. Are these WDM drivers and not BDA? If so could someone please help me locate the needed drivers? I've been trying to get it working for over 3 hours to no avail.
Thank you
#2
Broadlogic 2030 is listed as being supported.
WDM drivers used. BDA devices normally have BDA mentioned in their names or details.
You will find a specific device in 'Modules' folder, that comes with .INI file and a readme.txt
This is all I can tell, as I don't have that device..
WDM drivers used. BDA devices normally have BDA mentioned in their names or details.
You will find a specific device in 'Modules' folder, that comes with .INI file and a readme.txt
This is all I can tell, as I don't have that device..
My signature:
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
#3
Thank you for your reply.
I did read the readme.txt but the module does not appear in the device list so I cannot select it. I'm guessing it must be because as per the first note: "won't show up in device list unless you have the broadlogic drivers installed correctly", but I'm quite lost since as I stated in my previous message it does show up in device manager.
I guess I'll just wait and maybe someone with this card will read this thread.
Thank you
I did read the readme.txt but the module does not appear in the device list so I cannot select it. I'm guessing it must be because as per the first note: "won't show up in device list unless you have the broadlogic drivers installed correctly", but I'm quite lost since as I stated in my previous message it does show up in device manager.
I guess I'll just wait and maybe someone with this card will read this thread.
Thank you