hi
I am from germany. I installed progdvb v 6.10.1 on my computer with windows vista 32 bit. I started the programm, chose Germany - all channels and then i started to search for the channels (Channel list - Channel search - {BDA} AF9015 BDA Filter.
After a few minutes (1 to57) it got only 4 channels (the prosieben group). Same problem by searching with Blindsearch or ScanTransponder.
It cannot be a problem with the signal, because i got every 26 channels with the offical software of the stick on the same place.
The Receiver: MSI DigiVox mini2 (V.3.0)
Thank you
(Sorry, english is not my native language)
#2
I don't have that kind of trouble over here.
Perhaps you should get precise transponder data for your region, from sources like ueberallfernsehen.de or local providers.
May well be, your transponders have an offset against standard frequencies, due to local situation, that ProgDVB can't handle properly, or the data rates used are non-standard.
Perhaps you should get precise transponder data for your region, from sources like ueberallfernsehen.de or local providers.
May well be, your transponders have an offset against standard frequencies, due to local situation, that ProgDVB can't handle properly, or the data rates used are non-standard.
My signature:
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
#3
I have done it with the manual frequences of the region. Nothing changed.
But now it works...
I think it was a problem with the device list, because yesterday there were 4 devices marked with the green card. Today I disabled 3 of them and now I got only bda.
thank you...
But now it works...
I think it was a problem with the device list, because yesterday there were 4 devices marked with the green card. Today I disabled 3 of them and now I got only bda.
thank you...