Display posts from previous
Sort by

#3 by bonpas3
Hi,
Thank you very much for your answer... I've try to re install Progdvb (V4.80 and an older version) but the following message is now displayed :" Device not started " ...
Do you have any idea about what i should do ?

Even in the settings panel, device couldn't be started (LNB settings = OK).
The Skystar 2 card work properly with the Technisat soft.

Thank you very much for your help

#4 by SiLencer
Have no such problems here ...working fine...
but the following message is now displayed :" Device not started " ...
Do you have any idea about what i should do ?
before you start progdvb ...all parts of the technisat software (even the data App) must be closed...

then start progdvb and start your card in the device list menu...must work !

#5 by bonpas3
Hi SiLencer,

Thank you very much for your help, i will try it this evening at home
Could you please tell me if i have to close some application if i start progdvb just after booting the PC ?
I'm not sure to be clear : do you know if some part of the Technisat software are launched automatically ?

Thank you for your help

#6 by SiLencer
do you know if some part of the Technisat software are launched automatically ?
Yes , the data app launch automatically (Autostart folder)...Green/red circle in systray...

Hi

#7 by Chief23
Hi,

i have got the same Problem, a Skystar 2 PCI Card and it's always saying device not yet started. I closed all skystarproducts in my taskmanager, same problem.

is there any other thing i can try ?


thanks

Chief23

#8 by SiLencer
is there any other thing i can try ?
Not much..because the card is running as a network device ..check and adjust your Firewall Settings (also included XP Firewall)...
I closed all skystarproducts in my taskmanager

so progdvb should works..try to start skystar 2 device after start of progdvb in the device list...

#9 by stevec5000
I just installed ProgDVB and I get the same error, Device Not started !
Skystar 1 over TT Hard Mode [Card 1], when it starts. Then when I try to scan a transponder it freezes.
This piece of crap doesn't work and there's no support is there?

#11 by Juergen
stevec5000 wrote:...
This piece of crap doesn't work and there's no support is there?
What do you want, free pizza and beer with it?

SS1 based cards are working fine with ProgDVB, here and for many thousands of other users.

There's an announcement thread on bug reports and other complaints, please start to read there.

Full details on your dish set, LNB(s) and bird(s) used, switch(es) if existing, and on all your relevant settings, including LNB / DiSEqC controls. And precise description of what's happening.
BTW, does the original application work? Which version?
Else no way to help you, sorry.
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#12 by stevec5000
Could you make that pepperoni please?
Actually I finally did get it to scan but it takes so long that I thought
it must be freezing and I gave up before it finished.
Also, DBVviewer can play the PBS HD channel in 1920x1080 with sound
but ProgDVB is so slow that all I got was a series of jerky stills.
Is there some way to speed it up by something like 100X, otherwise
it just not going to work out?

#13 by Juergen
Pepperoni beer, oh my god :shock:

Regarding the HD 1080 issue, compare all codec and renderer settings.

Can't help more on this, as my machine won't do HD at all.
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#14 by keninishna
I have a skystar 2 and I am getting the same problem "device not started!" - skystar2 I have no other dvb programs open and ALTdvb and dream dvb work fine. I installed the drivers manually in devices and not by running the install exe if that makes any difference.

#15 by Hekto
I have the same problem whith SkyStar2 PCI Rev.2.6 (SkyNET.sys v.4.3.2.9999) after upgrade ProgDVB from 4.74 to 4.80.3
ProgDvbEngine
Device not started!
(Sky Star 2)
Stop/Start device in Device list give the same message.

update: after update driver to v.4.4.0 all work fine.