Hi guys,
I downloaded the latest progdvb installed and try to setup LNB under DiSeqC but there is not green or gray dots infect there is nothing at all except the card name. Could someone please help me with this?
Here's my setup.
Win XP
DVB-S 100 card from KWorld
ProgDVB 5.x
When I click on Settings --> Device List I can see the card and I have enabled/started it. Than I click on Settings --> DiSeqC I only see the card name but no green or gray dot to configure. On the side I see the option to add LNB but when I click on it nothing happens. Please help.
#2
Don't have your device, nor any 5.x version of ProgDVB running right now.
Does the original software package work, that came with your hardware?
It's always a good idea, to get that running first.
If your device uses BDA drivers, instead of normal WDM ones, it's possible, ProgDVB does not provide DiSEqC on it.
What do the comments tell, that are visible if the device is marked in the device list?
When using DiSEqC, you have to select the DiSEqC mode and then add the switch first, afterwards add LNBs to it's ports and set their properties.
Does the original software package work, that came with your hardware?
It's always a good idea, to get that running first.
If your device uses BDA drivers, instead of normal WDM ones, it's possible, ProgDVB does not provide DiSEqC on it.
What do the comments tell, that are visible if the device is marked in the device list?
When using DiSEqC, you have to select the DiSEqC mode and then add the switch first, afterwards add LNBs to it's ports and set their properties.
My signature:
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>
Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!
I don't give support by e-mail or PM.
And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!
NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.
Please keep it in English here, or Russian in the Russian section, or German in the German section.
I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!
1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode
19.2°,13°,28.x°E,30°W, DiSEqC 1.0
Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>