Display posts from previous
Sort by

#2 by Juergen
could i use the usal with progdvb?
Taken from progdvb.com:
Changes in current versions:
...
4.78 Support diseq 1.1
4.78 Support USALS (requst more tests).
No manual, sorry.

BTW, AFAIK the Stab uses power supply from the receiver's LNB supply.
This for it may be making more sense, to connect it to the Nexus, as that's got a bit more powerful DC supply.

No card is better or worse in general, both have their benefits and limitations, like any hardware in the world. Depends on your wishes and needs...
You shuld have thought about this before purchase, normally...
Normally you can use both at the same time, but in your case you have to decide, which one will move the dish, of course.

Don't change LNB cables with PC or receiver powered up!
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#4 by Juergen
Not personally, sorry. No such hardware here.

And Prog told, more tests were required. Don't know if they are ready with this now.
But you may feel free to test as well.
Normally things should work, basically, as the technical standards - like controls, timings and such - are public.
But occasionally there may also occur hardware specific issues, you can never know...
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#5 by DaDag
Since the ProdDVB 4.80 I use my TT 2300S to drive my STAB120 in USALS mode without any problem, very easy to setup and stable, before I used the DiSeQC 1.2 mode coming with ProgDVB since one year ago, but with setup not so easy (position pre adjusted using USALS receiver)

#9 by modernart
Hi,

i have a STAB120. Never got it running with USALS.
I adjusted manually either with kvadiseq or with the builtin
positioner tools of progdvb.

It would be much nicer to use USALS but there is no
manual.

Regards

modernart