Solved on my system in version 7.0.1.1
Thank you.

I confirm this behavior.
The same software configuration. Hardware is a Skystar HD/TT S2 3600 card.

ProgDVB Pro 6.95.4
Diseqc 1.1 doesn't work (or stopped working, I can not tell) with my TechnoTrend S2-3200 card.
Computer restart and power down/restart doesn't bring anything. Only channels on the default or last active input are visible.
Reverting to 6.95.3 solves the program (no configuration ...

Hello,

Since i have a problem with the minimal SR my card can handle, i've written a command tool to fix the satellite ini file for a minimal SR.

Usage: SatListFix <inputfile> <outputfile> <minimum_sr>
e.g. SatListFix 3592.ini new.ini 6000

The program will eliminate all transponders below the ...

Hi Prog,

I don't think it should be there - sorry for contradicting you :-) but my system requirement job makes me turn it on all sides...
If you have 2 hardwares in the system, one could be ok and the other with the problem - and in the "other" section it is a global setting (or you put in a list ...

Hello,

Normally such a SR limitation is PC hardware related. If you have it at LNB level, for a 16 LNB diseqc 1.1 setup, you have to set it 16 times :-) And it could be ok for one specific LNB unless there appears a new transponder witk low SR, and than you have the problem back...

So in my ...

As i signaled in earlier posts, i have a problem on satellite scan on my Skystar HD (with BDA drivers), when the scan progress just hangs, the scanning ending with "Device not found".
I traced the problem back to the fact that the symbol rate is to small for some transponders for the given hardware ...

Heh...

Reinstalled a fresh copy of 6.80.1 in another folder and it worked ok.
Reinstalled fresh in the same folder and it seems ok.
Now maybe this was transponder content related (feed) or some odd registry values or old registered filters which became normal....
I can not explain it and can not ...

If I remember correctly (it is now about 4 years...), they didn't work stable on Vista. I installed the TT ones and never tried again the original since the TT ones worked perfectly for me since 2008.
But the hardware is identical, including the same PnP identifiers.

Technisat Skystar HD (the same with Technotrend S2-3200) running with ttbudget BDA driver 5.0.1.8 on Vista32.
Setup is with diseqc 1.1 switch 1/10 with 10 LNB, from 39E to 0.8W

I tried drivers from 5.0.0.6 to 5.0.18, and one vista driver "installed by force" version 5.0.3.5 (it said vista but doesn ...

I got a strange behavior on 6.80.1 Pro during scanning.

e.g. satellite 16.0E has 71 transponders defined in all.list. When scanning, it starts with 1 of 71 and then switches to 102 total transponders which is not correct. Later, on transponder 40 the scanning crashes with message "Device not ...

Ok. Found out what really happened (and yes, it is 32bit):
I use C:\DVB\ProgDVB for installation. Usually the update installs by default in the same location, so i don't check the path :roll:
This one installed default in C:\Program Files\ProgDVB and i didn't noticed. Since the shortcut was updated ...

Now 6.73.1 was really an update one of a kind...

1. Had to re-register/activate
2. Lost diseqc settings
3. Lost favorite channel lists
4. Settings reverted to default
5. Plugins have disappeared. Only FTA.

Reverted to 6.73...
Plugins are still gone - Plugins menu is empty.
Only FTA work.

Any idea ...