Display posts from previous
Sort by

#2 by Juergen
You should post all relevant details on your dish system, to perhaps get helped. Without those it's absolutely impossible...
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#5 by Juergen
scb wrote:Windows Vista, skystar HD2, .... what more ???

satelites Sirius Hotbird Astra
...with a DiSEqC switch, I suppose.
Or is it a motorized system?

Anyway, Prog is correct, your dynamic channel list(s) can be set up to show positions to your liking (and access), and there can be more than one, and each can hold more than one position.
A channel list is not the original channel data base (where scanned stations go to), but more like a collection of links to it.
This for, you can also force a given satellite list, to show or not show stations from a position, after a successful scan.
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>

#7 by Juergen
Looks like if your DiSEqC is not switching.
To verify, bypass it temporarily and connect the Astra or Hotbird LNB directly, scan again.
If DiSEqC switching indeed fails, there may be several reasons for this.
Most common cause is not having the proper device settings selected, or using a tuner and driver, that does not yet provide those (on a BDA platform).
But there may also be some different source of trouble, like long and / or bad LNB cables, losing to much of the 22kHz signal, or a bad tuner or switch, or in rare cases grounding or interference problems (like from some nasty switch mode PSUs or CRT monitors / TVs, to close to the LNB cable).
My signature:

Please read here:
On Bug Reports And Other Complaints
and there:
BOARD RULES - READ THIS!


I don't give support by e-mail or PM.

And I will never assist on PayTV hacking.
PM ME FOR THIS AND YOUR ACCOUNT WILL BE DELETED IMMEDIATELY, WITHOUT ANY WARNING!!!

NEVER EVER DARE TO CONTACT ME FOR PRO VERSION ISSUES!
I am not responsible for that.
Check the 'Activation' section.

Please keep it in English here, or Russian in the Russian section, or German in the German section.

I don't read nor write Klingonian or any other language than English and German.
Addressing me personally in any exotic language will be treated as severe insulting! Be warned!!!

1.)AMD Phenom II x4 940, GA-MA770-UD3, 8 GB DDR2-6400. 7 Pro SP1 x64 + XP Pro SP3 x86
DVB-S2: Cynergy S2 USB HD
2.)P4 3200 i865G (F-S Scenic W600pwr) XP Pro SP3
DVB-S: hauppauge WinTV Nexus-S rev. 2.2, driver TT 2.19h, hardware mode

19.2°,13°,28.x°E,30°W, DiSEqC 1.0


Auf Deutsch:
DVB-Cube <<< Das deutsche DVB-Forum >>>